Fronius

Non-compatible inverters can be recorded using separate power meters or energy meters: Non-compatible inverters

• Integrate the inverter into the local network.
• Call up the user interface of the inverter via a browser.
• Make the following settings there:

• Activate the night mode of the data interface on the inverter display. Further information can be found here.

• Connect your laptop to the local network (via LAN cable or WLAN).
• Open the commissioning wizard in a browser at http://datamanager.
• Select Technician Wizard.

• Follow the installation steps and complete the forms in the submenus.
• Activate the radio button No limit in the Dynamic power submenu.

• Click Next and switch to the SOLAR WEB ASSISTANT.

• Activate the radio button dynamically.
• Click Connect.
• Follow the installation steps and complete the forms in the submenus. Click Save.
• Click the Settings button.
• Select the MODBUS menu item.
• Under Data output via Modbus, select the radio button tcp.
• Activate Inverter control via Modbus

• Click Save.
• Install the inverter on the SOLARWATT Manager via the Smart Setup

Night mode of the data interface

You must activate night mode so that the Fronius inverter can also be installed during the night or when there is insufficient DC voltage. The following settings must be made on the inverter display:

• Open the SETUP menu item on the inverter display.
• Select the Display settings submenu.
• Select the Night mode entry.
• Select the ON setting.
• Press Enter.

ATTENTION

Fronius inverters from the Primo GEN24 and Symo GEN24 series are not found and installed in the SmartSetup Manager using autodiscovery. The device search must be carried out by entering the IP address of the inverter. If the IP address changes during operation, the connection between the inverter and the Manager will be lost.

We therefore recommend assigning a static IP address to the inverter. There are the following options for this:

• Via the network settings of the inverter
• Via the home network settings of the router ("Always assign the same IP address to the device")

• Open the local user interface of the inverter in a browser.
• Call up the Communication menu item.
• Select Modbus.
• Activate the option Slave as Modbus TCP and Inverter control via Modbus.
• Install the inverter on the SOLARWATT Manager via the Smart Setup

Fronius Solar Net is a communication protocol between Fronius inverters. It can be used to connect up to 100 devices with each other. Only one inverter (master) needs to be connected to the local data network.

• Define the device that is connected to the local network via Ethernet as the master in the settings.
• Define all other devices connected via Fronius Solar Net as slaves.
• Assign each device an individual DATCOM address (1 ... 100).
• Note the need to set a terminating resistor on the first and last inverter of the bus system.

For further information on installing a Fronius Solar Net, please refer to the manufacturer's documentation.

• Starting the SmartSetup

Certain inverter models are found and installed automatically (Automatic installation).

Other inverter models are installed by selecting the device driver and specifying the IP address or host name (manual installation).

Information on the installation types of the series can be found in the table at the end of this page.

Automatic installation

If the device is correctly configured and available in the network, it is automatically displayed in green in the device list.

• Connect additional devices if necessary
• Continue with SmartSetup PV systems

Manual installation

• In the Select devices drop-down menu, select or search for the corresponding driver (according to the table at the bottom of the page) for the inverter device.

• Select the search mode (according to the table at the bottom of the page) for the WR device.
• If required, enter the IP address or host name of the device and confirm with Add device to search.

• If necessary, add further devices to the search.
• When the search list is complete, click Search and install devices.

Correctly installed devices appear in the device list with the message: Device is installed. The list also shows the current generation data.

• If necessary, connect additional devices
• Continue with SmartSetup PV systems