Inverter vision
- Data sheetpdf download (703 KB)Datasheet SOLARWATT Battery vision three backup booster en
- Data sheetpdf download (652.2 KB)Datasheet Battery vision clusterbox en
- Data sheetpdf download (1.9 MB)Datasheet SOLARWATT Battery vision Inverter vision max en-UK
- Data sheetpdf download (741.4 KB)Datasheet SOLARWATT Battery vision one backup booster en
- Data sheetpdf download (1.1 MB)Datasheet SOLARWATT Battery vision Inverter vision three en-UK
- Data sheetpdf download (1.1 MB)Datasheet SOLARWATT Battery vision Inverter vision one en-UK
- Manualpdf download (1.4 MB)Sicherheitshinweise-Safety Instructions Inverter vision_backup booster_clusterbox_INT
- Manualpdf download (40.2 MB)Quickstart Guide Battery vision Inverter vision three int
- Manualpdf download (1.4 MB)Safety Instructions Battery vision top pack_pack INT
- Manualpdf download (27.5 MB)Quickstart Guide Battery vision Inverter vision one _INT
- Manualpdf download (21.7 MB)Quickstart Guide Battery vision clusterbox
- Certificatepdf download (945.7 KB)Certificate SOLARWATT_Inverter vision three_1.0_(12.0-15.0 kW)_G99_NI_A2-3 test report
- Certificatepdf download (1.1 MB)Certificate SOLARWATT Inverter vision one 1.0 (4.6-6.0kW) G99_NI_A2-3 test report
- Certificatepdf download (1.1 MB)Certificate SOLARWATT Inverter vision one 1.0 (4.6-6.0kW) G99_Amd 9_A2.3 test report
- Certificatepdf download (1.3 MB)Certificate SOLARWATT Inverter vision three 1.0 (6.0-10.0kW) _G98_issue2_Form C test report
Frequently asked questions
It is not possible to charge the battery in backup mode via an AC generator connected to the AC connection of the inverter. In backup mode, there is no mains voltage and no mains frequency, so the AC connection is switched off.
Currently, the only way to charge the battery in backup mode is via the PV modules connected directly to the vision one/three hybrid inverter.
Yes.
Instructions for how to perform a black-start of the system can be found in our online operating instructions.
https://www.solarwatt.co.uk/manuals/solarwatt-battery-vision/operation/behavior-during-a-power-cut
Does the main AC cable have to be disconnected in this case?
The AC main (grid) cable does not need to be disconnected. The system will immediately switch back to the mains when it is available again.
Yes, the feet are included with the Battery vision top pack, as well as a termination plug for the unused connection of the bottom Battery vision pack.
As a result, you'll need to open the Battery vision top pack box first - even though the installation starts with the bottom pack.
The maximum length is 100m.
We officially recommend the use of a shielded cable with twisted pairs for RS485 communication, e.g. LIYCY (TP) 2x2x0.34 mm² for indoor use, and for outdoor use a UV and weather-resistant equivalent cable that complies with the required IP protection class IP65. However, using two cores of a high-quality CAT5e Ethernet LAN cable will also work - just make sure to use a cable tester to check the pin outs before running the cable!
The only requirement is that one phase must not be loaded with more than 1/3 of the rated power.
SOLARWATT does not offer a wall bracket for Battery vision.
The battery must be placed on a stable solid surface and fixed to the wall with the included wall brackets (which secure the tower to the wall, but are not load bearing). Please observe the specified clearances:
https://www.solarwatt.co.uk/manuals/solarwatt-battery-vision/installation/installing-battery-vision
Solarwatt accepts no responsibility for individually created stands or brackets etc.
In accordance with our applicable warranty conditions for the product, Solarwatt also offers you voluntary warranty services for this expansion component, which apply independently of statutory warranty rights.
Activate the warranty here: https://solarwatt.my.site.com/forms/s/activation?language=en_US
Our warranty services apply to your battery system including the inverter, whereby the warranty period for the system starts with the initial commissioning. Our warranty conditions stipulate that for additional battery vision packs within the meaning of this system warranty, the start of the warranty period is backdated to the date of initial commissioning (see B 3. of the warranty conditions). The recording of the date of commissioning of the retrofitted battery vision packs serves to complete your system and does not mark the start of the warranty for the retrofitted battery vision pack.
No. The system must be connected to the power grid. Permanent stand-alone ("island mode") operation is not permitted.
Our 'Battery vision' system, consisting of the individual components 'Inverter vision' 'Battery vision pack and top pack' and 'Meter', can initially be operated maintenance-free; there are no mandatory requirements for maintenance work to be carried out to preserve their function.
However, the products are electrotechnical components that can be checked for safety and function as part of a recurring inspection of electrical systems or must be checked in public buildings. The term 'maintenance services' in the Solarwatt warranty conditions is to be understood in this context. In this case, the note for maintenance work in the online manual of the product applies: 'Only qualified installers who have been trained by Solarwatt may carry out service and maintenance work on Battery vision.'
https://www.solarwatt.co.uk/manuals/solarwatt-battery-vision/legal/safety-instructions